Spreader beam for nav skid lift

By making sure the centre of gravity is directly beneath the crane hook, the lift is as stable and safe as possible By making sure the centre of gravity is directly beneath the crane hook, the lift is as stable and safe as possible
Industry Database

A 6t capacity spreader beam has been claimed to be the linchpin in lifting navigation skids onto offshore structures.

Navigation skids are self contained navaids that guide vessel traffic and helicopters operating in Dutch waters of the North Sea.

Centre of gravity was a principle area of concern in each lift due to load dimensions. The MOD 6 spreader beam from Modulift combined with chain slings, wire rope slings, and attachment points that can rotate 360 degrees under load, to lift two 1.6t (1,600kg) skids from supply vessels onto each of three platforms. The same configuration also has been used to lift skids onto five other platforms last year and one offshore wind jacket in 2018. The base of the skids measure (approximately) 2m (6.6 ft.) by 2m and they stand 3m (9.8 ft.) high. They were lifted by crane onto the main deck where batteries were installed before being raised to the helideck and welded into place at predetermined positions.

Jansen Marine & Offshore Trading BV, of the Netherlands, delivered the scope of work to U.S.-headquartered Tideland Signal. A number of oil and gas platforms will be abandoned in the years to come in the North Sea, before they are decommissioned. In the period between shutdown and abandonment and actual removal, they remain a hazard and need to be marked to avoid collisions. Since they do not have mains power after abandonment, Jansen Marine, in close cooperation with Tideland Signal Ltd, supplies skids that include marine lanterns, aviation obstruction lights, and fog signals; fog detectors; remote monitoring via satellite; and more.

Robin Jansen, managing director at Jansen Marine, explained that the skids are essentially autonomous mobile platforms. They come in all shapes and sizes but typically are used for temporary marking of an offshore structure, such as a platform, monopile, or jacket. The company supplies several types of skids, with a distinction between a unit with or without photovoltaic (PV) modules. Both types are fitted with batteries, but only the one with PV modules is capable of charging them. Skids without such modules are commonly used for periods up to half a year versus the year-round utilisation possible with the more advanced system.

Robin Jansen said: “The skids have a relatively large wind surface compared to their mass and they are not symmetrical. In particular the weight of the batteries moves the centre of gravity to the back of the skid. Furthermore, in order to provide the strongest holding points for the lifting eyes, they are installed at the base of the skid. The large wind surface, the asymmetrical design, and the low position of the lifting eyes, can result in an unstable load during lifting. By making sure the centre of gravity is directly beneath the crane hook, the lift is as stable and safe as possible.”

By Jake Frith

Latest Press Releases

Damen Shiprepair Brest completes refit of Cunard’s Queen Elizabeth

Cunard’s Queen Elizabeth has left Damen Shiprepair Brest (DSBr) following a 12-day repair and refit ... Read more

InvaSave shipped to Las Palmas de Gran Canaria for demonstrations under INTERREG Programme “Atlantic Blue Port Services”

On Thursday 27 December, an InvaSave 300 Mobile Ballast Water Treatment System was transported from ... Read more

A masterpiece of engine design: STEYR MOTORS SEC 4-cylinder

STEYR MOTORS is proud to present the SEC 4-cylinder, the world's first monoblock common rail marine ... Read more

EMAR Offshore Services places order for Damen Tug ASD 2811

EMAR Offshore Services, a Netherlands-based dedicated maritime service company, has placed an order ... Read more

Seismic vessels Oceanic Sirius and Oceanic Vega complete tandem drydocking at Damen Shiprepair Amsterdam

Sister-ships Oceanic Sirius and Oceanic Vega have completed a round-the-clock, 10-day maintenance pr... Read more

Damen signs with Gerd Stensen for Stan Tug 1606

Damen Shipyards Group recently signed a contract with Gerd Stensen AS from Norway for the delivery o... Read more

View all